How To Draw A Triangle In Mathematica
Welcome to EDAboard.com
Welcome to our site! EDAboard.com is an international Electronics Give-and-take Forum focused on EDA software, circuits, schematics, books, theory, papers, asic, pld, 8051, DSP, Network, RF, Analog Design, PCB, Service Manuals... and a whole lot more! To participate you need to register. Registration is free. Click hither to register now.
how to depict triangle in HFSS?
- Thread starter geppei
- Offset appointment
- Status
- Not open for further replies.
- #i
- Joined
- Apr 20, 2006
- Messages
- 31
- Helped
- 0
- Reputation
- 0
- Reaction score
- 1
- Trophy points
- ane,286
- Action points
- i,489
Could anybody know it?
Thx
- #2
- Joined
- Dec 12, 2005
- Messages
- 25
- Helped
- ii
- Reputation
- 4
- Reaction score
- 2
- Trophy points
- 1,283
- Activity points
- 1,471
Salam
I accept used the HFSS, though not much. Still I am learning nearly information technology. According to my experience y'all can not draw the triangle it cocky. Only if y'all want to brand some conical shape that is possible. Every bit in the case of horn antenna simply it is matter of conecting the surfaces.
Regards
Asim
- #3
jallem
Avant-garde Member level 1
- Joined
- Jul 23, 2005
- Letters
- 452
- Helped
- 73
- Reputation
- 146
- Reaction score
- 10
- Trophy points
- ane,298
- Activity points
- iv,993
merely go >depict>line and draw a triangle formed
by three lines but make sure you lot close the
surface. If the surface is not encompass get to
>3Dmodeler>surface>cover faces....
- #4
- Joined
- Aug 23, 2006
- Messages
- 43
- Helped
- three
- Reputation
- six
- Reaction score
- 1
- Trophy points
- 1,288
- Action points
- ane,605
yous can also use equation to draw a triangle.
Depict-> equation based surface
or
Describe-> equation based curves.
Based on my view of points, the latter is more accurate than the start.
- #5
- Joined
- Jul 27, 2004
- Letters
- 250
- Helped
- 30
- Reputation
- 60
- Reaction score
- xiv
- Bays points
- 1,298
- Activity points
- one,180
its simple u tin can use coordinate entry method and draw triangle and then fill the enclosed area
- #half dozen
loucy
Avant-garde Member level i
- Joined
- Aug 26, 2001
- Letters
- 414
- Helped
- 24
- Reputation
- 48
- Reaction score
- 11
- Bays points
- 1,298
- Activity points
- 4,657
double click after you have drawn 3 points and two lien segments.
- #7
- Joined
- Feb 16, 2007
- Letters
- 10
- Helped
- four
- Reputation
- 8
- Reaction score
- four
- Bays points
- 1,283
- Action points
- one,334
Use Draw line to course trangle or any other geometry in 2D. Then Select the object, copy information technology and paste to get a duplicate. At present use motion to position for the desired thickness. And then select the 2 oblects (Control + click), from the card select 3D Modeller > Surface > connect to get the 3D model.
- #8
- Joined
- Oct 27, 2022
- Messages
- 4
- Helped
- 0
- Reputation
- 0
- Reaction score
- 0
- Trophy points
- 1,281
- Location
- Pilani, Rajasthan
- Activity points
- 1,299
thanx, its good stuff
- Status
- Not open for further replies.
Similar threads
- How to get isosceles triangle in HFSS
- Started by buzzi
- Replies: 1
- How to draw helixes in HFSS
- Started by astatine
- Replies: 4
- how to draw helical in hfss
- Started by rohandantu
- Replies: 0
- how to draw magnetron cavities in HFSS?
- Started by kurama
- Replies: 0
- How to draw slot antenna in HFSS
- Started by mouek_1989
- Replies: 1
Source: https://www.edaboard.com/threads/how-to-draw-triangle-in-hfss.72270/
Posted by: ruckersoetted.blogspot.com
0 Response to "How To Draw A Triangle In Mathematica"
Post a Comment